Airforce Condor Regulator with Dual Gauge V3 (First of its Kind for the Airforce and Gunpower Airguns)
We have upgraded the regulator internals for more consistent shots and lesser wait time between shots.
Would like to thank our customers for their feedback so we could make further improvements and upgrades based on your requirements to our regulators.
Have upgraded the fill ports and micro gauges to larger threads from our previous models so it adds more life to the regulators as well.
The most awaited upgrade is a larger plenum which is 30% more than the "Airforce Condor Regulator with Dual Gauge V2"
Another feature which would help you shoot heavier pellets at high power is the higher regulated pressure which can now be set up to 250 bar and beyond in these models.
By default, we would set these to 200 bar, if you have a specific requirement do let us know in the comments when you place the order and we shall make sure it's set to the requested pressure.
Enhanced the looks of the regulators and it's much sturdier than before and can handle up to 300 bar of input pressure and output (plenum) pressure.
(Tested to 500 bar for input and output pressure)
However, the Max working pressure should not be attempted beyond 300 bar for the fill and 200 bar for the output pressure.
Output range of the regulator can be internally adjusted from 100 bar to 200 bar now.
We can proudly say that our regulators are now available for sale and will do a great job on the Airforce condor and the Gunpower airguns shooting those heavier pellets at higher speeds.
Dual Gauge design:
No more guessing, what pressure the regulator is set at.
Gauge shows you the output (Regulated pressure) as well as the input pressure. (Tank pressure).
No more keeping track of shot counts or guessing and working hard to know the cut off pressure of your regulators.
Set the regulator to the sweet spot, speed your pellets performs the best and just watch for the regulated gauge to trip below what it was set for.
Foster fill nipple on the regulator for quick fill or tethering your airgun.
This regulator ensures that your tank retains the quick install and disconnect feature.
You don't want to be looking for the Spin-Loc Tool when you want to get started or done shooting.
Larger pre chamber on our regulators in which we have combined both power and consistent shot count.
Built like a tank and tested to 500 bar (working pressure must not exceed 300 bar) for safety.
The burst pressure for these regulators is beyond 600 bar so they are very safe for use.
Sturdy gauges with metallic body for the wilderness with the airforce and gunpower airguns.
You also know if your regulator has developed a leak, this has been a daunting task is the past.
One day of shooting, the zero of your airgun changes and you think the regulator is the culprit.
Could be true also might not have been the regulators fault at all. No more guessing.
Now many users would be concerned that it increases the length of pull due to the 2- and 1/2-inches length of the regulator.
So, we came up with a solution for that too.
Just screw on these regulators to the compact .35L CF buddy bottles (300 bar max fill) and you would be retaining your LOP.
Each regulator is filled to 300 bar for 24 hours before they ship to ensure they are free of leaks.
The best raw materials have been used to machine this regulator and to ensure we have a light, durable, safe and proven product.
They have been chosen, designed with materials and specs to the highest tolerances for the right job.
Safety is the highest priority for any of the products we manufacture.
Highly recommend u install these regulators on our .35L CF Buddy Bottles which have a 300 bar fill capacity and are compact also helps retain the Length of Pull and get more shots as the reg is set to higher output pressure.
If you need the ultimate shot count then the answer to it is our "1 Ltr Luxfer Carbon Composite Cylinders 300BAR (61cu)(1000cc)"
If you have your own tank with M18 x 1.5 threads, then it would be a direct fit as well
We have now launched a “Airforce Condor Regulator Adjust Regulated Pressure Assembly” for those who would like to easily adjust the regulated pressure.
Imp Note: Sale is only for the Regulator. You will be using the factory valve assembly which installs onto the mouth of the regulator (unless you have purchased a custom valve assembly from us) and the reg then screws into the factory buddy bottle you already have. (unless you have purchased a buddy bottle of higher rating and/or capacity)
BE SURE TO READ THE DOC FOR INSTALLATION WHICH IS SENT ON EMAIL BEFORE YOU BEGIN THE UPGRADES.
[MAKE SURE TO DEGAUSS THE TANK BEFORE ATTEMPTING THE UPGRADE. ONCE DEGAUSSED, YOU SHOULD BE ABLE TO PRESS THE VALVE WITH YOUR HANDS AND THERE SHOULD BE NO PRESSURE IN THE TANK. ALWAYS DOUBLE CHECK THE SAME BEFORE YOU START WITH THE DISSASSEMBLY)
Contact us if you need any customization and we shall be happy to get it done for you.
If you have any further query about the listed product you can use the above link to “Ask a Question”